---Advertisement---
Electrical & Electronics Engineering Power System

Power System Interview Question-Answer

By smart_answer13

Published on:

---Advertisement---

Q.1 A power system will have greater flexibility of operation if they have __________.

       A. Only Peak load plants operating in combination

       B. Only Base load plants operating in combination

       C. Only thermal power plants operating in combination

       D. Various types of power plants operating in combination

Ans : Various types of power plants operating in combination


Q.2 For a given power system, its zero and maximum regulation will occur at the impedance angle of

       A. 35

       B. 60

       C. 45

       D. 50

Ans : 45


Q.3 A 200 bus power system has 160 PQ bus. For achieving a load flow solution by N-R in polar coordinates, the minimum number of simultaneous equation to be solved is ___________?

       A. 334

       B. 359

       C. 357

       D. 345

Ans : Total number of equation = (40-1)*1 + (160*2) = 359


Q.4 Single line diagram of which of the following power system is possible?

       A. Balanced power system

       B. Power system with LG fault

       C. Power system with LL fault

       D. Power system with LLG fault

Ans : Balanced power system


Q.5 Single line diagram does not represents

       A. Neutral wire of transmission lines

       B. Star connection of transformer winding

       C. Ratings of machines

       D. Delta connection of transformer winding

Ans : Neutral wire of transmission lines


Q.6 In impedance diagram different power system elements are represented by symbols.

       A. True

       B. False

Ans : False


Q.7 In combined operation of several power plants the reserve capacity requirement is reduced.

       A. True

       B. False

Ans : True


Q.8 A 50 bus power system Ybus has 80% sparsity. The total number of transmission lines will be ___________

       A. 225

       B. 456

       C. 563

       D. 345

Ans : 225


Q.9 The given graph is the depiction of ________ on a large power system network.

       A. Ratings of machines

       B. Any of the mentioned

       C. Three phase motor getting short

       D. L-G fault

Ans :  L-G fault


Q.10 A power system has a maximum load of 15 MW. Annual load factor is 50%. The reserve capacity of plant is _____ if the plant capacity factor is 40%.

       A. 3.75 MW

       B. 7.75 MW

       C. 46.75 MW

       D. 8.75 MW

Ans : 3.75 MW


Q.11 A protection system engineer is planning to provide the complete protection, he can achieve this by ___________.

       A. a two phase fault relays and three earth fault relays

       B. a two phase fault relays and two earth fault relays

       C. two phase fault relays and three earth fault relays

       D. three phase fault relays and two earth fault relays

Ans : three phase fault relays and two earth fault relays


Q.12 The area under the load curve represents ____________.

       A. maximum demand

       B. load factor

       C. the average load on power system

       D. number of units generated

Ans : number of units generated


Q.13 If all the sequence voltages at the fault point in a power system are equal, then fault is __________.

       A. LLG fault

       B. Line to Line fault

       C. Line to Line fault

       D. LG fault

Ans : LLG fault


Q.14 If the power system network is at Vs∠δ and receiving end voltage is Vr∠0 consisting of the impedance of TL as (R+j5)Ω. For maximum power transfer to the load, the most appropriate value of resistance R should be __________.

       A. 1.732

       B. 3.45

       C. 5.2

       D. 5.2

Ans : 1.732


Q.15 Voltage regulation in the power system is __________.

       A. rise in voltage at sending end

       B. dip in voltage at sending end

       C. rise in voltage at receiving end

       D. dip in voltage at receiving end

Ans : rise in voltage at receiving end


Electrical Engineering Power System MCQ Questions Electronics Engineering Power System MCQ Questions Engineering Exam MCQ Power System MCQ Questions

smart_answer13

---Advertisement---

Related Post

Superposition Theorem MCQ (Interview-Exam) Question-Answer

Superposition Theorem MCQ (Interview-Exam) Question-Answer Q.1 In superposition theorem, when we consider the effect of one current source, all the other voltage sources are ____________.       ...

Source & Delta Star Transformations MCQ (Interview-Exam) Question-Answer

Source & Delta Star Transformations MCQ (Interview-Exam) Question-Answer Q.1 A voltage source connected in series with a resistor can be converted to a?        A. Current ...

Mesh Analysis and Nodal Analysis MCQ (Interview-Exam) Question-Answer

Mesh Analysis and Nodal Analysis MCQ (Interview-Exam) Question-Answer Q.1 Find the value of the currents I1, I2 and I3 flowing clockwise in the first, second and third mesh ...

Kirchhoff’s Laws and Network Solutions MCQ (Interview-Exam) Question-Answer

Kirchhoff’s Laws and Network Solutions MCQ (Interview-Exam) Question-Answer Q.1 Find the value of I1, I2 and I3.        A. -1.29A, -0.566A, 1.91A        B. ...

Leave a Comment